Align T-REX 300X Dominator Super Combo RTF

The Align T-REX 300X RTF is so tiny, and so compact, that it can evolve not onlyindoors, but also outdoors in 3D flights.

The T-REX 300X RTF (Ready to Fly), pre-assembled, combined with the ALIGN A10 transmitter and the MiniGRS gyro , makes flying easy.

The T-REX 300X is equipped with a DFC rotor head, the low CG and low wind resistance providing direct flight responses.
The carbon fiber main frame combined with a reinforcement plate improves torsional strength.
The battery slide and the bright red anodized motor give a modern design.
The tail boom is made of thick aluminum alloy for better torsional strength and increased durability.
In addition, the painted fiberglass canopy is lightweight and low wind resistance.

The T-REX 300X is equipped with a MiniGRS flybarless system specially designed for small ALIGN helicopters (sub-500 series).
It is light and simple with quick and easy adjustments, suitable for most pilots and beginners.
In addition, the high torque of the 300MX 3700KV 2216 high efficiency brushless motor contributes to a dramatic increase in power.
The high efficiency cooling system allows for regulation of the operating temperature during and after flights.
The DS450 and DS455 HV digital servos, supporting 8.4V output, allow for fast response and high torque.
The new 25A brushless speed controller provides an adjustable BEC voltage of 5~8.4V

Contents of the box

• T-REX 300X DOMINATOR Kit x 1 set
• Flybarless MiniGRS Module x 1 set
• Carbon Fiber Main Blade 230mm x 1 set
• Tail rotor blades 50mm x 1 set
• Brushless control 25A RCE-BL25A x 1
• Brushless motor 300MX (3700KV 2216) x 1
• Digital servo DS450 x 3
• Digital servo DS455 x 1
• 10 channel radio control Align A10 x 1 set
• MiniA.BUS receiver x 1
• RCC-3SX balancing charger set x 1
• Align 3S1P 11.1V 1300mAh 30C LiPo battery x 1

Specification T-REX 300X RTF

• Length: 476mm
• Height: 158mm
• Width: 88mm
• Main blade length: 230mm
• Main rotor diameter: 525mm
• Tail rotor diameter: 143mm
• Motor pinion: 14T
• Main drive gear: 115T
• Main drive pulley: 40T
• Rear drive gear: 13T
• Transmission ratio: 8.21:1:3.08
• Weight (excluding battery): 418g

Align A10 Radio Control Specification

• Channel: 10 channels
• Available models: airplane helicopter multicopter
• Frequency range: 2.408 ~ 2.475 GHz
• Power: Less than 20 dBm (for EU)
• System mode: 2.4G AFHDS 2A system
• Suitable voltage range: 4.0 ~ 6.0 VDC
• Receiving distance: 1000m in open field
• Low voltage warning: below 4.2V
• Weight: 485g (excluding battery)
• Size: 275x187x102mm

Align MiniA.BUS receiver specification

• Channel: 14 channels
• RX sensitivity: -105dBm
• RF range: 2.4055 ~ 2.475 GHz
• System mode: 2.4G AFHDS 2A system
• Power supply: 4.0 ~ 8.4 VDC
• Transmission distance: 150m in free field

Flybarless Align MiniGRS Module Specifications

• Operating voltage range: 3.5 to 8.4V
• Operating current consumption: <100 mA at 4.8 V
• Rotation detection rate: 300° per second
• Rudder yaw detection rate: 600°/s
• Sensor resolution: 12 BIT
• Swashplate support: 120° CCPM Swashplate
• Mode support: T-REX250, T-REX300, T-REX450, T-REX470, T-REX500
• Receiver support: ALIGN A10(A.BUS), Futaba S-FHSS, DSM2/DSMX
• Operating temperature: -20 ~ 65
• Operating humidity: 0% ~ 95%.
• Comply with RoHS
• Size: 37.6x22.4x13mm

Align RCC-3SX Charger and Balancer Specifications

• Input voltage: 100 VAC to 240 V (50/60 Hz)
• Output voltage: 2 dc 7.4 V / 3 dc 11.1 V
• Battery type supported: Li-polymer / Li-ion
• Charging method: DC/HV
• Charging current: 2A
• Size: 123x74.3x32mm
• Weight: 260g

Align Battery Specifications

• Output: 11.1V 1300mAh 14.4Wh (3S1P)
• Supports 5C
• Dimension: 74x36.5x21mm
• Weight: 115g
• Power cord 14AWG silicone. Heat resistance: 200°C / Current resistance: 50A